sound system. The output level for these jacks will be controlled by the ZONE VOLUME KNOB
(22). These RCA jacks send a low current, unbalanced output signal. These jacks should only be
used for shorter cable runs (under 15 feet) to signal processors or looping to another mixer.
48. RCA MASTER OUTPUTS - The Master Output includes a pair
XLR BALANCED JACKS (52)
as well as a pair of RCA Unbalanced Jacks. The RCA jacks send a low current unbalanced output
signal. These jacks should only be used for shorter cable runs to signal processors or looping to
another mixer. For cable runs greater than 15 feet use the
XLR BALANCED JACKS (52).
49. PLAYER A CONTROL - This jack is used to control the “Q-Start” function between the mixer
and a compatible American Audio
® or American DJ® CD Player. Using the mini plug included with
your CD player, connect from the CD player controller out jack to this jack. Player A “Q-Start”
functionallity will be controlled by the left side of the CROSSFADER (25). For more information on
“Q-Start” functionallity refer to the user manual included with your CD player. Be sure to only use
the mono tip mini plug included with your CD player to avoid damage to the mixer and/or the CD
player.
50. PLAYER B CONTROL - This jack is used to control the “Q-Start” function between the mixer
and a compatible American Audio
® or American DJ® CD Player. Using the mini plug included with
your CD player, connect from the CD player controller out jack to this jack. Player B “Q-Start”
functionallity will be controlled by the right side of the CROSSFADER (25). For more information on
“Q-Start” functionallity refer to the user manual included with your CD player. Be sure to only use
the mono tip mini plug included with your CD player to avoid damage to the mixer and/or the CD
player.
51. TRIM OUTPUT -
This knob is used to adjust the maximum voltage output level. Output voltage
wil range from 0v ~ 9v. This function may be used to limit the maximum siganl output level.
52. BALANCED XLR MASTER OUTPUTS JACKS - The Master Output includes a pair of XLR
Balanced jacks as well as a pair of RCA UNBALANCED JACKS (48)
. The 3-pin XLR jacks send a
high current balanced output signal. These jacks should be used when you will be driving an amp or
other audio equipment with a balanced input, or whenever you will be running a signal line greater
than 15 feet. Always, use these jacks whenever possible.
53. AC CONNECTION -
This connector is used to supply main power to the unit via the included
detachable power cord. The power connection uses an I.E.C. type connector, use only the supplied,
polarized AC power cord. Use only a power cord that matches this type of connection. Be sure to
only connect this unit to a power outlet that matches the printed power label on the unit. Never use
a power cord when the ground prong has been removed or broken off. The ground prong is used to
reduce the risk of electrical shock in case of an electrical short. This cord is designed to fit in one
direction only. Do not attempt to force a cord if it does not fit, be sure the cord is being inserted
properly.
54. AC VOLTAGE SELECTOR - This switch is used to change the operating voltage. Operating
voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is set to the proper
voltage for your area before attempting to operate the unit. Always be sure main power is shut off
before change the position of the Voltage Selector Switch.
©American Audio® - www.americanaudio.us - Q-FXPRO Instruction Manual Page 14
Q-FXPRO CONTROLS AND FUNCTIONS cont.
(26 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern