©American DJ Supply® - www.americandj.com - X-Calibur™ Instruction Manual Page 7 ©American DJ Supply® - www.americandj.com - X-Calibur™ Instruction Manual Page 8
P
S
CS DJ S
Ma e sure t e lamp is located in t e center o t e
re lector t en adjust t e lamp to t e best spot
nplug main power and wait or at least minutes be ore
opening t e ousing
or installing operating and maintaining t e de ice you a e
to be uali ied and ollow t e instruction manual.
eplace use bulb or spare parts only wit t e same type o parts.
Ma e sure t at neit er t e an nor t e enting slots are
co ered by decorati e material.
o user ser icable parts inside.
CC
C
CP
C
C
D
D P
S S
CS
8
8
DMX
PCMM
P DMX
P DMX
S DDSS P S
7 8
P
P
1765432
1. XLR Output Jack - This jack is used to send the incoming DMX
signal to another fi xture.
2. XLR Input Jack - This jack is used to accept a DMX input
signal.
3. Dip Switches - These switches are used to set the DMX
address. Each switch corresponds to a specifi c value based
on binary code.
4. Option switches - These switches will activate one of four
options:
Switch 1: Focus - When activated this switch will center
the mirror with a white spot. This will allow you to focus the
beam properly.
Switch 2: Self Test - When activate this function will acti-
vate a built in self test program.
Switch 3: Inverted Pan - When activated this switch will
invert the PAN value. Left will become right and vice
versa.
Switch 4: Inverted Tilt - When activated this switch will
invert the TILT value. Up will become down and vice
versa.
5. Lamp Housing - This cover enclose the lamp and lamp socket.
DMX512 IN
3-PIN XLR
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 3
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number ZDMX/T) will decrease the possibilities of erratic
behavior.
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fi xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
X-Calibur™ Set Up X-Calibur™ Fuse & Lamp Replacement
(48 Seiten)
(33 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern