American Audio PSX - REV 1-2 Bedienerhandbuch Seite 10
- Seite / 10
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
DCC Specialties, 57 River Rd, Suite 1023, Essex Jct., VT. 05452 800-671-0641, info@dccspecialties.com www.dccspecialties.com 10 of 10
Sequential Programming Instruction for Setting the Address and Programming CV’s
Digitrax: Using the DT-400/402
Setting PSX Addresses:
1. Disconnect PSX from DCC power
2. Move PSX Jumper to Program Position
3. Turn DCC power on “PWR”+ “ Y+”
4. After 30 seconds, reconnect DCC power Program CV's at this time (see below)
First, In CV 63,enteravalueof42toreset.Thenset any other CV's needed. Do not
Move Programming jumper or turn off power. .Exit program mode and go to step
5.
5. Press “SWCH” key to enter Switch Mode
6. Select the switch number to be set using the keypad or RH knob.
7. Press either the “OPTN” or “CLOC” key to set address.
8. Repeat steps 6 and 7 until all addresses set.
9. Press “EXIT” key to return to LOCO mode.
10. Turn DCC power off “PWR” “ N
–
“.
11. Move PSX Jumper to Run Position
12. Turn track power on. Test the switch address setting by using the
“SWCH” key and switch addresses.
13. Turn power off and put the program
j
umper into the Run position.
14. Turn DCC power on. Test the PSX using the switch commands.
Programming PSX CVs: Do Setting Addresses First, See Above
1. Disconnect PSX from DCC power.
2. Move PSX Jumper to Program Position
3. Turn DCC power on “PWR” “ Y+”
4. After a few seconds, connect DCC power to the PSX
5. Select an unused locomotive number with the keypad or RH knob.
6. Press “PROG “ key until you get from Pg to Po
7. Use LH throttle to set, dial the CV # and the RH throttle for the CV value.
8. Press, “ENTER”
9. Repeat ste
p
s 7 & 8 until all the CV values are set.
10. Press “EXIT”
Lenz: Using the LH100:
Setting PSX1’s Addresses:
1. Turn DCC power off.
2. Move PSX-
A
R Jumper to Program Position
3. Turn DCC power on
4. Press “F5" key to select “SW” mode.
5. Enter the switch number to be set using the keypad, then press ENTER.
6. Press either the “+” or “
–
” key to set the address. Let LED blink once.
7. To enter another address press the “CI” key.
8. Repeat steps 5 -7 until all addresses are set.
9. Press “ESC” key to return to normal.
10. Turn DCC power off.
11. Move PSX-
A
R Jumper to Run Position
12. Turn track power on.
13. Test the switch address setting using “SW” mode and the new switch
address(es).
Programming PSX1’s CVs:
1. Turn DCC power off.
2. Move PSX-
A
R Jumper to Program Position
3. Turn DCC power on.
4. Select a locomotive number with the keypad that
is unused on your layout.
5. Press the “F” keys and the “+” or “
–
” key to select “POM” mode then hit “Enter”.
6. Press “+” or “
–
” until “CV” is displayed then press “Enter”.
7. Key in the desired CV number then press “Enter”
8. Enter the CV value to change, then press “Enter”.
9. The display will show the CV number and value to be programmed.
10. Hit "Enter" to program the CV, note the LED on
the PSX-
A
R flashes when the key is released
11. Press "Esc" key to return to Step 7) or press
"Esc" three times to exit CV
programming
12. Turn power off and put the Program jumper into the Run position.
13. Turn DCC power on. Test the PSX-
A
R using the switch commands.
NCE: Us ing t he Pro Cab o r Po wer Ca b
Setting PSX1’s Addresses:
1. Turn DCC Power off.
2. Move PSX-
A
R Jumper to Program Position.
3. Turn DCC Power on.
4. Press SELECT ACCY.
5. Then use the keypad to enter the new switch number.
6. Press ENTER then press either 1 or 2 to set the address.
7. Repeat steps 4 thru 6 until all of the switch addresses are set.
8. Turn DCC Power off.
9. Move PSX-
A
R Jumper to Run Position.
10. Turn DCC Power on.
Test the switch setting using the SELECT ACCY key.
Programming PSX1’s CV
s
:
1. Turn DCC Power off.
2. Move PSX-
A
R Jumper to Program Position.
3. Turn DCC Power on.
4. Use SELECT LOCO to address an unused locomotive number.
5. Press PROG/ESC key to enter PROGRAM ON MAIN mode.
6. Key ENTER to select any unused locomotive number, then ENTER again.
7. Key 2 to enter PROG CV NUM.
8. Enter CV number then ENTER.
9. Enter value to be stored then ENTER.
10. Repeat steps 8 and 9 until finished.
11. Press PROG/ESC to return to normal operation.
12. Turn power off, put the PSX-
A
R Program Jumper into the Run position.
13. Turn power on.
Test the PSX-
A
RusingtheSELECTACCYkey.
MRC: Using the Prodigy Advance Cab:
Setting PSX1’s Addresses:
1. Turn DCC Power off.
2. Move PSX-
A
R Jumper to Pro
g
ram Position.
3. Turn DCC Power on.
4. Press ACCY key.
5. Then use the keypad to enter the new switch number.
6. Press ENTER then press either 1 or 2 to set the address.
7. Repeat steps 4 thru 6 until all of the CV value are set.
8. Turn DCC Power off.
9. Move PSX-
A
R Jumper to Run Position.
10. Turn DCC Power on.
Test the switch setting using the ACCY key.
Programming PSX1’s CVs:
1. Turn DCC Power off.
2. Move PSX-
A
R Jumper to Pro
g
ram Position.
3. Turn DCC Power on.
4. Press LOCO to address an key in an unused locomotive number.
5. Press PROG key to enter PROG MAIN TRACK mode, then press ENTER.
6. Continue to press ENTER until CV# is in the display.
7. Enter the CV number then ENTER.
8.EnterthevaluetobestoredintheCVthenENTER.
9. Repeat steps 8 and 9 until finished.
10. Press ENTER to return to normal operation.
11. Turn power off and put the PSX-
A
R Program Jumper into the Run
position.
12. Turn DCC power on.
Test the PSX-
A
R using the ACCY ke
y
.
Verwandte Produkte und Handbücher für Nein American Audio PSX - REV 1-2
(6 Seiten)
(26 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.577 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern